Recent Comments

How to Make An Authentic Native-American Arrow

SAFETY FIRST: Ask an adult to help with tools you haven't used before.


Click here for a PDF version of these instructions.

I make arrows the way my Iroquois ancestors did long ago. You can, too.

In our modern world, the hard part is getting the material, but you can use some alternatives that I’ve suggested.

Just remember: These arrows might look crude, but they’re not toys. Use them for target practice only, under the supervision of an adult, or display them in your room. Be careful!

— Gordon Soaring Hawk



  • Adult help and/or supervision
  • Quarter-inch or 5/16-inch dowels
  • Bone, metal or slate, ground to shape, for arrowheads
  • Stout thread or cordage to attach feathers and arrowheads to the shaft
  • Hot glue, wood glue or ferrule cement
  • Wing feathers from a craft store
  • Water- or oil-based paint



STEP 1: Shafts should be about as thick as your little finger and a couple of inches longer than the distance from your armpit to your fingertips. Make sure they’re straight as an arrow! After you gather them (get permission before cutting any growing thing), bundle them in groups of five and let dry for a few days. Dowels can be used as a substitute; they are available at lumber and building-supply stores.


STEP 2: Once the shaft is dry, scrape off the bark until the wood is smooth.


STEP 3: Cut a notch (about as deep as the diameter of the shaft) for the bowstring by scraping one end with a sharp stone. To get a sharp stone, find a piece of quartzite cobble (river stone) and break it in half with another rock. At the end of the shaft that receives the arrowhead, scrape out a notch that is 3/8 – to 5/8-inch deep. You can also use a knife, small saw or file.


STEP 4: Grind an arrowhead into the right shape by scraping the material against a sidewalk until the arrowhead has a point and a sharp edge. It’s a simple but tedious process. For safer arrowheads, you can round off the point.


STEP 5: Using the sharp rock, gouge a notch on either side of the wide end of the arrowhead for holding the cordage.


STEP 6: Place the arrowhead in the notch, wrap it with a piece of cordage 8 to 10 inches long and glue it with hot glue. I use resin, which is made from boiling pitch (sap) from trees. Making resin can be dangerous because natural turpentines must be burned off. For cordage, I use sinew, which I prepare by pounding deer tendons between rocks, then separate them into long, stringy fibers. Before I can use the sinew, I must chew it. The enzymes in saliva help dissolve the collagen that holds the tissues together, and this is what makes it work like glue. (Soaking it in water won’t work.)


STEP 7: For fletching (arranging) the feathers on your arrows, make sure each vane comes from the same side of the wing. Split each feather down the middle of the spine (use scissors or pocketknife) and trim it to size.


STEP 8: Glue the feathers onto the shaft, making sure the top feather is aligned with the bowstring notch, then space the two others equally from the first. Wrap more thread around each end of the feathers and set the arrow aside to dry for a day.


STEP 9: Once the wrappings are dry, the arrow is ready for painting. I put animal fat in a tin can and melt it in the sun. Then I mix in some reddish earth and daub it on the arrow with a paintbrush. You can use watercolors or oil-based paint.

Now it’s time for target practice!

Submit a Photo of Your Project

Important Note: Please only upload photos of your project. Because of privacy rules, we can't post any photos that show people's faces. Always ask for your parent's permission before uploading anything to a website.

10 Comments on How to Make An Authentic Native-American Arrow

  1. nice arrow but u need like months the grind the arrow head to goos shape with hands

  2. giggidygoo // June 10, 2008 at 9:16 pm // Reply

    bowman13 the correct way tomake the notches is to simply use a nail filer this will create a simple but yet affective arrow.

  3. where do u get fethers¿

  4. ace of spades // May 17, 2008 at 8:49 pm // Reply

    if you live in ohio simply go down to flint ridge.there is tons and tons of flint there but if u find a flint arrow head keep it dont put it on the arrow oh and this really helped me out thanks!

  5. how do i tell different knids of wood apart

  6. flintstone // April 24, 2008 at 5:57 pm // Reply

    is it ok that I use flint rock?

  7. crackerjackzach // April 11, 2008 at 12:41 pm // Reply

    its a good method but it looks hard

  8. i use deer antlers for my arrow heads…i have way to many antlers hangin and i cant find any good sharp rock so i though of the antlers…they work if the antlers are fresh or they lose the wieght from age…

  9. BigPapaSmurf // March 9, 2008 at 12:10 pm // Reply

    thx…. this info will help me to create an arrow for my NAS 200 class

  10. this is a good usefull way to use up boring hours u spend on playing computor games and watching tv, i like being creative and this is a good fun way to waste boring t.v time.

Leave a Reply to Cool dude Cancel reply

Please don't use your real name.