Recent Comments

Make your own weather instruments

weather-map

Learn more about weather and meteorology by completing these weather-related projects.


MAKE A WIND VANE

A wind vane measures the direction of the wind.

What You’ll Need

  • Aluminum baking dish, pie tin or tray that’s thin enough to cut
  • Wooden garden stake that’s at least 3 feet tall and 1 inch thick
  • 12-inch-long, 1-inch-thick piece of wood
  • 2- to 3-inch-long nail
  • Drill
  • Metal washer
  • Hammer
  • Mallet
  • Glue
  • Small saw
  • Scissors

What You’ll Do

weathervane31. Using the mallet, drive the garden stake into the ground until it feels sturdy. Choose a location that’s outdoors and relatively clear of anything that would obstruct the wind.

2. Using the saw, cut a half-inch slot into each end of the 12-inch-long piece of wood.

3. With the help of an adult, place the piece of wood on top of the stake, and drill a hole through the wood and into the stake. Use a drill bit that’s slightly larger than the nail you’ll be using.

 

weathervane44. Place the washer on top of the stake, and insert the nail through the wood and into the stake. The piece of wood should be free to rotate but not fall off.

 

weathervane25. Cut an arrowhead and tail out of the aluminum, and glue them into the slots on each end of the wood.

 

weathervane16. Wait for the wind to blow, and watch as your vane turns to point in the same direction.


MAKE AN ANEMOMETER

An anemometer measures the speed of the wind.

What You’ll Need

  • New sharpened pencil
  • 5 plastic foam cups
  • Hole punch
  • Straight pin
  • 2 long plastic straws
  • Felt marker
  • Tape

What You’ll Do

anemometer51. Mark a number “1” on one of the cups and set it to the side.

2. Poke four holes evenly spaced apart in the sides of the cup by plunging the pencil straight through both sides. Make sure one set of holes is slightly lower than the other.

 

anemometer43. Poke the pencil through the bottom of the cup, then pull it out, turn it around, and push it through the hole again, this time with the eraser side up.

 

anemometer34. Thread straws through the holes of the cup so that they cross in the middle. Tape the straws in place.

 

anemometer25. Push the pencil up until the eraser touches the straws at the point where they cross. Push the straight pin through the straws and into the eraser so that the straws are held in place, but the cup can still spin around the pencil.

6. Using the pencil, poke one hole in the side of each remaining cup. Mount each cup on the straws.

 

anemometer17. Hold the apparatus by the pencil, wait for the wind to blow, and watch it spin. Count the number of revolutions the marked cup makes in one minute to track the wind speed.


MAKE A RAIN GAUGE

weather-200x148A rain gauge measures the amount of rain.

What You’ll Do

You can make a rain gauge out of any kind of measuring cup left outside when it rains.

If an old measuring cup isn’t handy, cut the top off of a plastic water bottle. Use a ruler to measure how much water the bottle collects after a rainfall, or, better yet, use a waterproof marker to make inch marks on the side of the bottle.


36 Comments on Make your own weather instruments

  1. you need to put in a barmoneter

  2. i just want to make the rain gauge, but I’m still saving this to my favorites list

  3. how do you make a barometer

  4. this realy works

  5. so hard

  6. charmed one // April 18, 2011 at 6:40 pm // Reply

    looks really hard and boring!

  7. Science club // October 17, 2010 at 11:21 am // Reply

    What a great idea on the anemometer! We are studying weather in our after school club. What is the formula to calculate the number of spins for wind speed?

  8. Wow, great timing! We JUST got notice that we have to make a weather instrument as a project for school!

  9. this is cool! :)

1 2 3

Leave a Comment

Please do not use your real name.